Faculty of Engineering
Department of Manufacturing Engineering
Faculty of Engineering
Department of Manufacturing Engineering

 


THE ANNALS OF "DUNAREA DE JOS" UNIVERSITY OF GALATI

Fascicle V, Technologies in Machine Building

ISSN 1221-4566

Fascicle V, Year 2011 - Volume I

1. V. Paunoiu, F. Quadrini, N. Baroiu, Al. Epureanu - NUMERICAL STUDY ABOUT THE INFLUENCE OF INTERPOLATOR ELASTIC MODULUS IN RECONFIGURABLE MULTIPOINT FORMING

2. S. Berbinschi, V. Teodor, N. Baroiu, N. Oancea - RING TANGENTIAL TOOL TOPOLOGICAL REPRESENTATION OF PERIPHERAL SURFACES

3. S. Berbinschi, V. Teodor, N. Oancea - A 3D METHOD FOR PROFILING THE SHAPING TOOL FOR GENERATION OF THE HELICAL SURFACES

4. S. Berbinschi, V. Teodor, N. Oancea - A GRAPHICAL METHOD DEVELOPED IN THE CATIA DESIGN ENVIRONMNET FOR THE MODELING OF GENERATION BY ENVELOPING

5. F.B. Marin, V. Teodor, I.C. Constantin, A. Epureanu - VIDEO COLLISION WARNING SYSTEM BASED ON TOPOLOGICAL APPROACH

6. L.C. Popa, V. Teodor, I. Popa, N. Oancea - SURFACE PROFILING METHOD OF THE DISK CUTTER OF THE FEMALE ROTOR FROM THE SCREW COMPRESSOR COMPONENT

7. L.C. Popa, V. Teodor, I. Popa, N. Oancea - SURFACE PROFILING METHOD OF THE DISK CUTTER OF THE MALE ROTOR FROM THE SCREW COMPRESSOR COMPONENT

8. V. Teodor, I. Popa, D. Schiopu - AN ALGORITHM FOR REGISTRATION OF POINTS MEASURED ON COORDINATE MEASURING MACHINE

9. C. Stoian - DYNAMICS OF THE SYSTEM FOR FEED KINEMATICAL CHAIN HYDROSTATIC DRIVING

10. F.B. Marin, A. Epureanu, C. Maier, V. Marinescu - COMPUTER VISION BASED TECHNIQUE FOR ONLINE MONITORING OF BLANK GEOMETRY IN SHEET METAL FORMING PROCESSES

11. M. Vasie, L. Andrei - NONCIRCULAR GEAR DESIGN AND GENERATION BY RACK CUTTER

12. V. Paunoiu, V. Teodor, A. Epureanu, E. Gavan, G. Bercu - NEURAL NETWORK APPLICATION TO THE RECONFIGURABLE MULTIPOINT FORMING PROCESS

13. N. Baroiu, V. Teodor, N. Dumitrascu, N. Oancea - COMPARATIVE ANALITICAL MODELS FOR SHARPENING OF MULTI-FLUTE DRILLS WITH CURVED CUTTING EDGES



Fascicle   V, Year 2011 - Volume II

1. F. Susac, I. Constantin, M. Banu, A. Epureanu, F. Potecasu, M. Marin - TOWARDS IMPROVED MECHANICAL PROPERTIES OF ALUMINUM ALLOY CAST PARTS

2. N. Baroiu, S. Berbinschi, V. Teodor, C. Urse - MODELLING AND SIMULATION OF THE MANUFACTURING OF A TWISTED DRILL WITH THREE CURVED CUTTING EDGES, USING THE SV& TOOLBOX SOFTWARE

3. S. Berbinschi, F.J. Santos Martin, N. Baroiu, V. Teodor - TOPOLOGICAL REPRESENTATION OF ROTATING CUTTER RECIPROCALLY ENVELOPING WITH A HELICAL SURFACE

4. G. Frumusanu, I. Constantin, Al. Epureanu - A NOVEL CONTROL SYSTEM FOR CHATTER SUPPRESSION IN TURNING

5. S. Berbinschi, V. Teodor, N. Baroiu, N. Oancea - PROFILING METHODOLOGY FOR SIDE MILL TOOLS FOR GENERATION OF HELICAL COMPRESOR ROTOR USING REVERSE ENGINEERING

6. S. Berbinschi, V. Teodor, N. Baroiu, N. Oancea - ENWRAPPING SURFACES WITH POINT CONTACT � COMPARISSON BETWEEN CATIA METHOD AND ANALITICAL ONE

7. L.C. Popa, I. Popa, V. Teodor, N. Baroiu - PROFILING TOOL GENERATING METHOD, USING THE PROFILE MEASUREMENT OF ROTOR OF SCREW COMPRESSOR COMPONENTS

8. S. Patriche, M. Banu, C. Onisor, C.L. Musat - HARMFUL EFFECT OF CHEMICAL COMPOUNDS USED IN AGRICULTURE ON THE HUMAN HEALTH

9. C. Maier, V. Marinescu, V. Paunoiu, I. Constantin - IMPROVED PART QUALITY IN COMPLEX DEEP DRAWING USING VARIABLE DRAW BEAD MOTION CONTROL

10. V. Paunoiu, V. Teodor, C. Maier, N. Baroiu, G. Bercu - STUDY OF THE TOOL GEOMETRY IN RECONFIGURABLE MULTIPOINT FORMING

11. M. Afteni, M. Banu, V. Paunoiu, I. Constantin - INFLUENCE OF THE TOOLS GEOMETRY ON THE DEEP-DRAWING FORCE

12. M. Afteni, M. Banu, V. Paunoiu, I. Constantin - NUMERICAL AND EXPERIMENTAL INVESTIGATIONS OF THE NICKEL THIN SHEETS MICRO-DEEP DRAWING PROCESS

13. I.V. Ion, F. Popescu - FINITE-TIME THERMODYNAMICS BASED ECOLOGICAL ANALYSIS OF AN IRREVERSIBLE RANKINE HEAT ENGINE

14. St. Bordei, F. Popescu - AERODYNAMIC RESULTS FOR A NOTCHBACK RACE CAR